home *** CD-ROM | disk | FTP | other *** search
/ Magnum One / Magnum One (Mid-American Digital) (Disc Manufacturing).iso / d22 / wd.arc / V3M22 < prev    next >
Text File  |  1991-05-17  |  9KB  |  227 lines

  1.  
  2.      Western Digital is a registered trademark of Western Digital 
  3.      Corporation; IBM PC, AT and XT are registered trademarks of the 
  4.      International Business Machines Corporation; MS DOS, OS2 and PC DOS 
  5.      and Xenix are registered trademarks of Microsoft Corporation.  
  6.      Speedstor is a registered trademark of Storage Dimensions; Disk 
  7.      Manager is a registered trademark of Ontrack Computer Corporation.  
  8.      SCO is a registered trademark of The Santa Crux Operation.
  9.      
  10.                                  WD1003V-MM1/MM2
  11.      
  12.                                    User Guide
  13.      
  14.      
  15.      The WD1003V-MM1 controller is designed to interface with up to two 
  16.      Winchester ST506/ST412 MFM hard disk drives in an IBM PC AT or compatible 
  17.      system and will support drives with up to 16 read/write heads and 
  18.      2048 cylinders.  Each drive may be a different configuration.  
  19.      
  20.      The WD1003V-MM2 also supports up to two floppy disk drives including 
  21.      360 KB, 720 KB, 1.2 Megabyte, and 1.44 Megabyte drives (5-1/4 inch or 
  22.      3-1/2 inch).  The WD1003V-MM2 also supports "intelligent" 1.44 
  23.      Megabyte media drives.  These intelligent drives obtain the drive 
  24.      type and data rate from the drive's media and do not depend upon the 
  25.      state of J1 pin 2 for this information.  
  26.  
  27.      INSTALLATION
  28.  
  29.      This section briefly describes the installation of the controller board.  
  30.      Do NOT use the WD1003V-MM2 with an AT configured, AT compatible, or XT 
  31.      floppy controller in the same system.  Removal of the extra floppy 
  32.      controller is necessary for proper operation of the WD1003V-MM2.  
  33.      Disabling the floppy controller on the WD1003V-MM2 is NOT possible.
  34.      
  35.      A minor incompatibility exists between the WD1003V-MM1 (or WD1003V-MM2) 
  36.      and the WD1003-WAH (or WD1003-WA2).  If the drive contains more than eight 
  37.  
  38.      heads, e.g. a 16 head drive, the WD1003-WAH numbers heads 8 through 15 as 
  39.      0 through 7 in media's ID fields.  The WD1003V controllers number heads 8 
  40.      through 15 as 8 through 15.  To correct this problem, install a jumper on 
  41.      W1 pin 7-8 when using the WD1006V controller on a drive formatted with the 
  42.  
  43.      WD1003-WAH or WD1003-WA2.  This problem is not manifested in drives with 
  44.      less than eight heads.
  45.      
  46.                
  47.      Installation of the controller requires three steps:  1) verifying 
  48.      jumper settings; 2) installing into the host computer; 3) formatting 
  49.      the hard disk drives.  To complete installation, you will need the 
  50.      following:
  51.      
  52.      Two hard disk cables (3 if using 2 hard disk drives); Winchester hard 
  53.      disk drive; screwdriver; MSDOS Version 2.0 or later; IBM Advanced 
  54.      Diagnostic diskette (or similar program for IBM compatibles); FDISK 
  55.      and Format utility (normally included with MSDOS).
  56.      
  57.                             Preparation of Controller
  58.      
  59.                                      WARNING
  60.                  HANDLE THE CONTROLLER BY THE ENDS OF THE BOARD
  61.                 SOME OF THE CHIPS ARE STATIC SENSITIVE AND DAMAGE
  62.                   MAY OCCUR IF THE BOARD IS INCORRECTLY HANDLED
  63.      
  64.      Before you can install your WD1003V-MM1 or MM2, you will need to be 
  65.      certain that the jumpers (small shorting plugs) are correctly set.  
  66.      Refer to Table 1 for correct jumper settings.  Modification of 
  67.      factory jumper settings is rarely necessary.  Modify jumpers only 
  68.      under the direction of a qualified individual; i.e. your dealer.
  69.      
  70.  
  71.      
  72.                 
  73.                 ┌──LED───Drive1──Drive0─Control──Floppy──────┐
  74.                 │ J6───┐  J3───┐ J4───┐ J5─────┐ J1─────┐    │
  75.                 │  └───┘  └────┘ └────┘ └──────┘ └──────┘    │
  76.                 │             W1 ∙∙∙                         │
  77.                 │                ∙∙∙         W3 ∙∙           │
  78.                 │                            W4 ∙∙           │
  79.                 │                            W5 ∙∙           │
  80.                 │                                            │
  81.                 │                                        ∙   │
  82.                 │                                      W6∙   │
  83.                 │ WD1003V-MM1/MM2                            │
  84.                 └────────────┐    ┌─┐                    ┌───┘
  85.                              └┴┴┴┴┘ └┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┘
  86.                 
  87.                       All jumpers OFF for factory defaults
  88.  
  89.                 
  90.                                                       Table 1
  91.      
  92.      Jumper     Position      Function
  93.      
  94.      W1         1-2 OFF       Standard:  Hard drive(s) in latched mode
  95.      
  96.                 1-2 ON        Hard drives in non-latched mode.
  97.      
  98.                 3-4 OFF       Standard: Four byte ECC.
  99.      
  100.                 3-4 ON        Reserved
  101.      
  102.                 5-6 OFF       Standard:  Cacheing enabled
  103.      
  104.                 5-6 ON        Cacheing disabled.
  105.  
  106.                 7-8 OFF       Format incompatible with WD1003-WAH (WA2)
  107.      
  108.                 7-8 ON        Format compatible with WD1003-WAH (WA2)
  109.           
  110.      W3         1-2 OFF       Standard:  Primary I/O Address Hard Disk 
  111.                               Drive
  112.      
  113.                 1-2 ON        Secondary I/O Address Hard Disk Drive
  114.      
  115.      W4         1-2 OFF       Standard:  Primary floppy I/O addresses
  116.      
  117.                 1-2 ON        Secondary floppy I/O addresses.
  118.      
  119.      W5         1-2 OFF       Standard: Single speed floppy drives**
  120.      
  121.                 1-2 ON        Dual speed floppy drives.**
  122.      
  123.      W6         1-2 OFF       Standard: Bracket ground option not used.
  124.      
  125.  
  126.  
  127.  
  128.  
  129.  
  130.  
  131.  
  132.  
  133.  
  134.  
  135.  
  136.  
  137.      
  138.                 1-2 ON        Connects bracket to board ground.
  139.      *Not all jumper headers are installed.  Modify jumpers only under
  140.       the direction of a qualified individual.
  141.  
  142.      **DO NOT COMBINE SINGLE AND DUAL SPEED DRIVES IN THE SAME SYSTEM**
  143.      
  144.      
  145.                               Hardware Installation
  146.      
  147.                                      WARNING
  148.                         MAKE SURE COMPUTER IS TURNED OFF
  149.                             AND POWER IS DISCONNECTED
  150.      
  151.      1.  Verify that your host computer has a 135 watt power supply.  If 
  152.      the disk drive(s) is(are) being installed internally, it is best to 
  153.      locate the controller in the nearest available expansion slot to the 
  154.      drive.
  155.      
  156.      2.  Remove the blank expansion slot bracket.  Put the bracket away 
  157.      and save it for possible future use.  The screw will be used to hold 
  158.      the new controller in place.
  159.      
  160.      3.  The terminating resistor must be present only on the last hard 
  161.      disk drive connected.  If there are two drives, the terminating 
  162.      resistor must be present on the second drive.  Verify proper setting 
  163.      of drive select switches for drive select 1 or 2. Refer to your 
  164.      system owner's manual for information about proper drive termination 
  165.      and select switches.  DO NOT USE THE RADIAL SELECT OPTION.
  166.      
  167.      NOTE:  IF USING THE WD1003V-MM2 WITH BUILT IN FLOPPY CONTROLLER...
  168.      
  169.      DO NOT ATTEMPT TO USE WITH ANY OTHER FLOPPY CONTROLLER.  IT IS NOT 
  170.      POSSIBLE TO DISABLE THE FLOPPY CONTROLLER ON THE WD1003V-MM2.  
  171.      
  172.      4.  Attach 34-pin control connector to J5 on the controller board.  
  173.      Make sure that Pin 1 of the cable connector goes to Pin 1 on the 
  174.      controller board.  Pin 1 of the cable connector is typically located 
  175.      on the color coded side of the cable.
  176.      
  177.      5.   Connect control cable to drive.
  178.      
  179.      6.   Attach 20-pin data connector to J4 (Drive C or 0).
  180.      
  181.      7.   Attach 20-pin data connector to J3 (Drive D or 1).
  182.      
  183.      8.   Connect data cables to drives.
  184.      
  185.      9.   Attach Winchester activity LED connector to J6.  
  186.      
  187.  
  188.  
  189.  
  190.  
  191.  
  192.  
  193.  
  194.  
  195.  
  196.  
  197.  
  198.  
  199.  
  200.  
  201.  
  202.  
  203.      
  204.      FOR WD1003V-MM2 USERS:
  205.      
  206.      10.  Attach the floppy cable connector to J1.
  207.      
  208.      11.  Attach cable to floppy drive(s).
  209.      
  210.                                       NOTE
  211.      Remove or disable any other floppy controller in your system.  The
  212.      WD floppy controller cannot be disabled.
  213.  
  214.      THE FLOPPY CABLE IS NOT THE SAME AS THE CABLE USED TO CONNECT 
  215.      THE HARD DISK DRIVES.
  216.      
  217.      13.  Install controller board into the expansion slot. Make sure that 
  218.      the board is seated properly by pressing down on both ends of the 
  219.      board.  Secure the board with the bracket screw.
  220.      
  221.                                      CAUTION
  222.                   WHEN ROUTING CABLES, BE CAREFUL NOT TO PINCH
  223.                   THEM.  CABLES MUST NOT GET CAUGHT BETWEEN THE
  224.                  COVER AND THE BOARDS, NOR SHOULD THEY OBSTRUCT
  225.                       ANY AIR FLOW PATH FROM FANS OR VENTS.
  226.  
  227.